Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Mar Vista Homeowners
Your chimney cap takes the brunt of every rainstorm that rolls across Mar Vista, and the crown underneath it quietly cracks from years of sun and temperature change. When either fails, water gets into the flue and the masonry, and that’s where rusted dampers, stained ceilings and crumbling mortar begin. Our technicians have up to 12 years of experience fitting caps and rebuilding crowns on homes across the westside, using Olympia Chimney and Famco caps rather than generic hardware-store covers. We book sweeps and cap work Sunday through Friday, with fast dispatch from 7am to 7pm, and same-day appointments often open up. Call (855) 337-2073 to get your cap or crown looked at.
What Our Chimney Cap & Crown Service Includes
Caps and crowns are two different parts of the same job, and both protect the chimney from the top down. Here’s what each piece of the work involves when we take it on in Mar Vista.
Cap Installation
A chimney cap is the metal cover that sits over the flue opening, keeping rain, birds and debris out while letting smoke escape. If your flue is open to the sky, you’re one storm away from water running straight down into the firebox. We install Olympia Chimney and Famco caps sized to your flue, and the same visit covers the measurement and the fitting, so there’s no quote-then-order delay.

Cap Replacement
Caps rust, warp or blow loose over time, especially the thin galvanized covers that come with some builder-grade chimneys. A damaged cap is worse than no cap because a bent or missing top lets water pool around the flue tile. We pull the old cap, check the flue and crown underneath, and fit a replacement built for the weather here. If the cap was the only thing holding back a bigger problem, we’ll show you what we find before recommending anything.

Crown Repair
The crown is the concrete or masonry cap at the very top of the chimney that sheds water away from the brick. Hairline cracks let moisture in, and after a few winters that moisture works into the mortar below. We repair crowns by removing loose material, refilling cracks and rebuilding the slope so water runs off instead of sitting. Where the crown is too far gone to patch, we rebuild it.

Crown Coating
Crown coating is a flexible, weather-resistant seal applied over the crown to close small cracks and protect the surface from the sun. It’s a good option when the crown is sound but showing wear, and it’s far less expensive than a rebuild. We use Gelco crown coating, which is made for masonry crowns and flexes with the natural movement of the chimney. Coating is not a fix for a structurally failing crown, and we’ll tell you plainly if yours is past the point where a coating will hold.
Multi-Flue Cap
Some Mar Vista homes have chimneys with more than one flue, either from a second fireplace or a furnace vent sharing the stack. A single-flue cap won’t cover that, so you need a multi-flue cap sized to span the whole top. We build and fit multi-flue caps that cover every opening at once, with the right clearance for each flue. That keeps water and animals out of all the flues without capping one and leaving the others exposed.
Custom Cap
Older homes, unusual chimney shapes and oversized stacks sometimes don’t fit a standard cap. A custom cap is made to the exact dimensions of your chimney top so it sits flush and seals properly. We measure on site and have the cap fabricated to fit, then install it on a return visit. Custom work takes a little longer, but it’s the right answer when a stock cap would sit loose or leave gaps.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We work with Olympia Chimney caps because they’re built to last in exposed positions and come in sizes that fit most residential flues. When we fit an Olympia cap, we’re matching the model to the flue and the draft, not just grabbing whatever’s on the shelf. Famco caps are the other line we install regularly, and we know how their covers handle rain and wind over the long haul.
For crown work, Gelco coating is what we reach for when the crown needs a protective seal, and we know where that coating performs and where it doesn’t. We also work with HeatShield for liner restoration when a failing crown has let water into the flue and the liner needs attention. Whether you have Olympia Chimney, Famco, Gelco or any other make on your chimney, we can help.
Signs You Need Chimney Cap & Crown Right Now
- Water in the firebox after rain. If you see dampness, rust or a water stain inside the firebox, the cap or crown is likely letting water in. It’s a small fix now and a masonry repair later if it’s ignored.
- A cracked or crumbling crown. Look at the top of the chimney from the ground; visible cracks or missing chunks mean water is getting into the brick. That moisture travels down and damages mortar and flue tile over time.
- Rust on the damper or firebox. Rust inside the firebox usually points to moisture coming from above, not from the room. The cap and crown are the first places we check.
- Birds, squirrels or debris in the flue. An open or damaged flue lets animals nest inside, which blocks the draft and creates a fire hazard. A properly fitted cap keeps them out.
- A cap that’s loose, bent or missing. Wind can lift a poorly fitted cap right off. A loose cap rattles, a missing one leaves the flue wide open, and either way it needs attention before the next storm.
Our Chimney Cap & Crown Process – Step by Step
- 1
We start with a look at the whole chimney. Before we touch the cap or crown, we check the flue, the firebox and the masonry so we understand what’s actually going on. That way we’re not fixing the top and missing a problem lower down.
- 2
We measure and document. We measure the flue and the chimney top, take photos, and note the condition of the existing cap and crown. You get a clear picture of what we found, not just a verdict.
- 3
We give you a written estimate. The estimate sets out what needs doing and why, with the price for the job. Nothing gets recommended without evidence you can see for yourself, and we’ll tell you plainly when work can safely wait.
- 4
We do the work in one visit where possible. Because we install Olympia Chimney and Famco caps, product selection and fitting happen together rather than over two appointments. Crown repair and coating are handled in the same visit when the scope allows.
- 5
We check the fit and clean up. After the cap or crown is in place, we confirm it’s seated and sealed, then leave the area as we found it. If a follow-up visit is needed for a custom cap, we schedule it before we leave.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Mar Vista?
A typical cap installation in Mar Vista runs $250 – $550 depending on the flue size and the cap you choose, and crown repair usually falls in the $350 – $900 range, with a full crown rebuild on the higher end. Crown coating is the least expensive option at roughly $200 – $400 when the crown is still sound. Multi-flue and custom caps sit a little higher because of the extra fabrication and fitting.
| Service | Typical Estimated Range |
|---|---|
| Cap installation (single flue) | $250 – $550 |
| Cap replacement | $250 – $600 |
| Crown coating | $200 – $400 |
| Crown repair | $350 – $900 |
| Multi-flue or custom cap | $500 – $1,200 |
What moves the price is the size and condition of the crown, how accessible the chimney top is, and whether the damage has spread into the flue or masonry. You avoid overpaying by getting a written estimate that names the work and the reason for it, and by asking to see the photos. Our estimate is free, and the written estimate sets the final price. Call (855) 337-2073 for an exact quote.
Chimney Cap & Crown Near Mar Vista – Our Service Area
We cover Mar Vista and the surrounding westside, including Culver City, Venice, Marina del Rey, Westchester and Santa Monica. We also serve Ladera Heights, Westwood, Brentwood, Beverly Hills, Inglewood and View Park-Windsor Hills. Dispatch runs Sunday through Friday, 7am to 7pm, and we book cap and crown work by appointment, with same-day slots when they’re open. Learn more about our chimney cap & crown work in nearby Culver City, or see our Chimney Sweep Mar Vista page for the full service picture.
Serving Mar Vista, CA – Our Local Coverage Area
We serve Mar Vista and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Mar Vista
A chimney cap is the metal cover over the flue opening that keeps rain, animals and debris out, while the crown is the concrete or masonry top that sheds water away from the brick. The cap protects the flue, and the crown protects the chimney structure itself. You need both working to keep water from getting into the chimney.
Most cap installations and crown coatings are done in a single visit of a couple of hours. Crown repair can take longer if the masonry needs rebuilding, and a custom cap needs a measurement visit before the fabrication and installation visit. We’ll give you the timing in your written estimate so you know what to expect.
Most cap installation in Mar Vista runs $250 – $550, crown coating about $200 – $400, and crown repair $350 – $900 depending on the damage. The written estimate sets the final price, and the estimate itself is free. Call (855) 337-2073 for an exact quote.
Yes, we install Olympia Chimney and Famco caps, along with Gelco coating for crown work and HeatShield for liner restoration when water damage has reached the flue. Because we fit the product and do the install in one visit, you’re not waiting on a separate order. If your chimney already has a cap from another maker, we can still work on it.
Same-day appointments are often available depending on the schedule, and you can book by phone. We answer 24/7, and dispatch runs Sunday through Friday, 7am to 7pm. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm.
We stand behind the work we do and will go over what’s covered in your written estimate before the job starts. If something isn’t right after the install, call us and we’ll take a look. The estimate spells out the terms so there are no surprises.
Clear access to the fireplace and the area around the chimney base, and let us know about any pets or gate codes. You don’t need to do anything to the chimney itself; we handle the inspection and the work. Having any previous inspection reports on hand helps us understand the history.
Schedule Your Chimney Cap & Crown Service in Mar Vista Today
A failed cap or a cracked crown is a small repair now and a bigger one after the next rainy season. Call (855) 337-2073 to book a free estimate on cap installation, crown repair or coating anywhere in Mar Vista. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. No-obligation estimate, and we’ll show you what we find before recommending anything.
Written by the team at Chimney Sweep Mar Vista.